Laminated Plastic

Laminated Plastic

2.02 MATERIALS AND PRODUCTS

  1. Panels, Urinal Screens and Doors: Shall be 1” thick, of 1/16” general purpose laminated plastic. Edge laminate to be applied first and secured via hot melt adhesive. All shall be constructed of a sandwich of laminated plastic bonded under pressure to a solid particleboard core with a minimum density average of 48 lbs/cu. ft., with the highest quality non-flammable adhesive assuring a rigid permanent bond. Doors to be pre-notched and recessed to accommodate concealed controlled non-rising spring tension hinges. Where doors are pre-notched and recessed for hardware and fittings, the exposed core shall be sealed against moisture.
  2. Metropolitan Pilasters: Shall be 1-1/4” thick, constructed the same as the panels, doors, and urinal screens. Bottom of pilasters shall have adjustable floor anchor, with leveling device, anchor studs and locking nuts to firmly secure pilasters to the floor. This entire assembly to be concealed with a 3” high stainless steel plinth, secured in place with concealed clips.
  3. Headrail: Pilasters, when set in place, shall be securely braced with 1” x 1-1/2” anodized anti-grip headrail bracing. Headrail to seat on top of pilaster and securely fastened onto top of the pilasters with theft-resistant screws.
  4. New Yorker Pilasters: Shall be 1-1/4” thick, constructed the same as the panels, doors, and urinal screens. Pilasters, when set in place, shall be securely anchored to concrete sub-floor by means of 3/8” diameter cadmium plated bolts with a minimum penetration of two inches, secured rigidly into concrete slab with expansion shields and secured to the pilasters through a heavy cast leg integrally fastened to the pilaster core. This entire assembly to be concealed with a 3” high stainless steel plinth, secured in place with concealed clips.
  5. Empire Pilasters: Shall be 1-1/4” thick, constructed the same as the panels, doors, and urinal screens. Pilasters, when set in place, shall be securely anchored to overhead carrying member (overhead members to be furnished, installed and drilled by others) by means of 3/8” diameter cadmium plated bolts secured to the pilasters through a heavy cast leg integrally fastened to the pilaster core. This entire assembly to be concealed with a 3” high stainless steel plinth, secured in place with concealed clips.
  6. Gramercy Pilasters: Shall be 1-1/4” thick, constructed the same as the panels, doors and urinal screens. Both the top and the bottom of the pilasters shall have adjustable anchor and leveling devices. Anchor studs and locking nuts designed to firmly secure the pilaster to the floor and ceiling. Both assemblies to be concealed with 3” high stainless steel plinths, secured in place with concealed clips.
  7. Hardware and Fittings: Panels and pilasters shall be attached to one another and/or to walls with Zamac chrome plated brackets. Doors shall be equipped with Knickerbocker Ever Life Spring Activated Non-Rising hinges. Top Hinge Pivot Door Bracket to be recessed and inset into edge of door, approximately 2” below the top with a pivot pin, operating on a self-lubricating bushing, mounted within the door structure, supported both above and below the pivot bracket. Operation of door shall be controlled by opposing cams under spring tension, mounted on a fixed vertical pintle. Hinges to be adjustable to permit door to rest at any angle, or to hold door open or closed when not latched. Hinges shall operate without raising or lowering the door on a fixed horizontal plane. Each door shall be equipped with stop and keeper, combination coat hook and bumper and concealed latch, featuring a latch cover which permits access to the compartment in case of emergency. Handicap door to be equipped with Knickerbocker Lever Handle. Design to comply with ADA requirements. Hinge bracket and stops shall have clamp flanges to transmit the strain of door closing to the pilaster. All hardware shall be heavy one-piece, non-ferrous “Zamac” casting, heavily chrome plated. Hinges, stop and keeper, pilaster and panel brackets shall be thru-bolted with sex bolts having theft-resistant heads.

 

COLORS

As selected from color guide.